6284 جودةمواصفات الورقة

6284 جودة مواصفات الورقة

Low and intermediate strength, atmospheric corrosion resistant structural steels

رموز الحروف القابلة لإعادة الإنتاج --> HRUKK --> KRKK --> L --> LKK --> LRKK --> RKK
البدائل3012 3015 3281 6018

Flat / Hot Rolled

Flat steel products are obtained by heating semi-finished products with a rectangular cross-section (slab), which are produced by the continuous casting method, to a specific temperature and then rolling them, with thicknesses ranging from 1.40 to 25.40 mm and widths ranging from 700 to 2025 mm, produceed as coil or by cutting/slit-coiling flat steel products from coils.

Low and intermediate strength, atmospheric corrosion resistant structural steels

التركيب الكيميائي (%)

المعيار المكافئرقم جودة إرديميرCmax.Mnmax.Pmax.Smax.Simax.Cumax.CEmax.
المعيارجودة
EN 10025-2:2019S355J2 (Cu)62840.201.600.0250.0250.550.550.45
  1. Max carbon equivalent (CE) is increased by 0.01 % for Si ≤ 0.25%, and 0.02 % for Si ≤ 0.04 %
  2. The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020%.
  3. Carbon equivalent, CEV (IIW) % = C + Mn / 6 + (Cr + Mo + V) / 5 + (Ni + Cu) / 15
  4. If Cu %: 0.25-0.40, max carbon equivalent (CEV) is increased 0.02 % within the framework of agreements with customers.
  5. Deoxidation method of this products is fully-killed. Minimum aluminium to nitrogen ratio is 2:1.

الخواص الميكانيكية

المعيار المكافئرقم جودة إرديميرRe [N/mm2] t(thickness, mm)Rm [N/mm2] t(thickness, mm)A(%) min. t(thickness, mm)Impact
المعيارجودة
1.8≤t≤1616.01≤t≤261.8≤t≤2.993≤t≤26A801.8≤t≤2A802.01≤t≤2.5A802.51≤t≤2.99A53≤t≤26Temperature ( ° C)6≤t≤7.49KVC J min.6≤t≤7.49Temperature ( ° C)7.5≤t≤9.99KVC J min.7.5≤t≤9.99Temperature ( ° C)10≤t≤26KVC J min.10≤t≤26
EN 10025-2:2019S355J2 (Cu)6284355 min.345 min.510-680470-63014151620-2014-2021-2027
  1. Tensile test values apply to "transverse" test pieces
  2. Impact test is not carried out for thickness thinner than 6 mm.
  3. Could be normalized or equivalent to normalized rolling.

Flat / Plate

Heavy plate products are obtained by rolling semi-finished products with a rectangular cross-section (slab) produced by the continuous casting method to a specific temperature, with thicknesses ranging from 6.00 to 200.00 mm and widths ranging from 1000 to 3600 mm.

Low and intermediate strength, atmospheric corrosion resistant structural steels

التركيب الكيميائي (%)

المعيار المكافئرقم جودة إرديميرالسماكة (مم)Cmax.Mnmax.Pmax.Smax.Simax.Cumax.CEmax.
المعيارجودة
EN 10025-2:2019S355J2 (Cu)62846≤t≤300.201.600.0250.0250.550.550.45
EN 10025-2:2019S355J2 (Cu)628430.01≤t≤600.221.600.0250.0250.550.550.47
  1. Max carbon equivalent (CE) is increased by 0.01 % for Si ≤ 0.25%, and 0.02 % for Si ≤ 0.04 %
  2. The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020%.
  3. Carbon equivalent, CEV (IIW) % = C + Mn / 6 + (Cr + Mo + V) / 5 + (Ni + Cu) / 15
  4. If Cu %: 0.25-0.40, max carbon equivalent (CEV) is increased 0.02 % within the framework of agreements with customers.
  5. Deoxidation method of this products is fully-killed. Minimum aluminium to nitrogen ratio is 2:1.
  6. C = 0.22 % max. for thickness greater than 30 mm,

الخواص الميكانيكية

المعيار المكافئرقم جودة إرديميرRe [N/mm2] t(thickness, mm)Rm [N/mm2]A(%) min. t(thickness, mm)Impact
المعيارجودة
6≤t≤1616.01≤t≤4040.01≤t≤60A56≤t≤40A540.01≤t≤60Temperature ( ° C)6≤t≤7.49KVC J min.6≤t≤7.49Temperature ( ° C)7.5≤t≤9.99KVC J min.7.5≤t≤9.99Temperature ( ° C)10≤t≤100KVC J min.10≤t≤100
EN 10025-2:2019S355J2 (Cu)6284355 min.345 min.335 min.470-6302019-2014-2021-2027
  1. Tensile test values apply to "transverse" test pieces
  2. Impact test is not carried out for thickness thinner than 6 mm.
  3. Could be normalized or equivalent to normalized rolling.